4x4Wire

About you, your 4x4 and access
John Stewart

When Springs Break (Part 3)

Broken spring with 'spring splint' installed'The "Spring Saga" began with "Options for the height challengedwhich was a spring-over lift for my 1994 Jeep YJ.  As I was replacing a 4 inch spring lift, new springs were necessary.  The basic lift components were Rubicon Express and I opted for Rubicon Express springs which provided 1.5 inch of spring lift in addition to the spring-over lift.  I was able to remove the two inch body lift and still clear 35 inch tires.  

While the combination was a great performer on the articulation challenges of Ocotillo Wells SVRA, a major deficiency was soon apparent.  The Rubicon Express springs were not up to the stress of extreme flexing.  In Part 1 of “When springs break”, emergency repairs were made in order to get off the trail and into the shop for correct repairs.  Time was of importance as Tierra del Sol Desert Safari 47 was coming.  Part 2 of "When springs break" covered the install of a spring hanger reversal and new main leaf springs in the front to replace one broken and one bent spring.  I did make it to Desert Safari and some wheeling.  Final day, while driving slow on a washboard road, I heard an ominous snap.  This time, a rear main leaf spring snapped.  At least this time I had the proper “spring splint” kit to provide emergency repair.

Continue reading
  6551 Hits
John Stewart

When Springs Break (Part 2)

Shackle Reversal Spring Hanger

When Springs Break (Part 1) covered the basics of spring flex and potential problem that can arise.   Springs are a critical part of your suspension to provide for tire contact with the ground and keep the axle of your 4x4 centered while allowing movement.  So, what are solutions to reducing the chance of spring failure?  Certainly, moving to a coil spring suspension is one option to eliminate the flex issue with leaf springs.  Another option is to install to a shackle reversal.  That is a simpler and more cost effective option.

As noted in Part 1, leaf springs have a fixed point and a movable point.  For the front leaf springs, the fixed point is about mid-center of the vehicle.  When the front wheel encounters an obstacle, it is pushed back against the fixed point.  The force can cause undue stress on the spring and a potential for breaking near the rearward spring hanger: the fixed point.

Continue reading
  7864 Hits
John Stewart

When springs break...

There comes a time when venturing off road that leaf springs do fail.  Your day of 4x4 fun comes to an abrupt end.

Such an occurrence recently happened to me. Luckily, the main leaf spring did not completely break and I was able to make it home after some scrounging and rigging a "splint" to keep the spring from flexing and completing the break.

Time for a little break analysis.  For starters, the springs were new when installed with the spring-over lift in November and had seen 6 days of on the trail use.  Springs are designed to flex and should offer trouble free action over an extended life.  Spring failure can result from abnormal stress or metal weakness due to improper tempering.

Continue reading
  8385 Hits
John Stewart

Exhausting Options

JBA Performance Exhaust HeaderOkay, the vibration was stopped.  New motor mounts in place, it was time to tackle the exhaust header.  The 4.0L engine is prone to exhaust header issues.  And, the exhaust is a critical part of an engine.  You can improve performance of an engine by increasing air flow through the engine.  Basically, the hot exhaust gases need to go somewhere.  Why not through clean bends of an aftermarket performance header?

The stock 4.0L exhaust manifold would not place well in an airflow test.  On the other hand, aftermarket headers are tubular and designed for efficient air flow.  

Take your pick.  There are several vendors providing quality products in a variety of price ranges.  Each has their advocates.  Some advocate for ceramic coating.  All agree on tubular construction.

Continue reading
  8425 Hits
John Stewart

Motor Mounts and Choices

YJ Motor MountsThere comes a time in the life of engines when items need to be replaced.  Such a time had come for my Wrangler.  It started with a little vibration under acceleration.  With over 130,000 miles, one motor mount was loose and a small leak had developed with the exhaust manifold.

The motor mount was an easy solution: after market or stock.  Actually, that provoked some discussion.  Turns out, the easy choice is not that easy.  While quality aftermarket products are available, they do come with a price.  In this case, it was about two for one.  In other words, I could get two stock motor mounts for less than the cost of one aftermarket motor mount.

Continue reading
  6719 Hits
4x4Wire.com

OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting. Copyright (c) 1999-2020 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission. You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material. All corporate trademarks are the property of their respective owners.